步科ET100自由串口协议编写问题 点击:2122 | 回复:2



zj1923278901

    
  • 精华:0帖
  • 求助:1帖
  • 帖子:2帖 | 1回
  • 年度积分:0
  • 历史总积分:10
  • 注册:2015年4月21日
发表于:2015-04-21 13:28:32
楼主

#include     <stdio.h>      /*标准输入输出定义*/

#include     <stdlib.h>     /*标准函数库定义*/

#include     <unistd.h>     /*Unix 标准函数定义*/

#include     <sys/types.h>  

#include     <sys/stat.h>   

#include     <fcntl.h>      /*文件控制定义*/

#include     <termios.h>    /*PPSIX 终端控制定义*/

#include     <errno.h>      /*错误号定义*/

#include <sys/time.h> 

#include <time.h>

#include     <stdbool.h>

#include      <sys/sem.h>


void Delay(int ms);

int ReadData(int fd, unsigned char *read_buff, int count, int ms);

int WriteData(int fd, unsigned char *read_buff, int count);

unsigned short Read_LW(unsigned int n);

void Write_LW(unsigned int n,unsigned short val);

void CopyToLW(unsigned int offset,const void *src, int n);

void CopyFromLW(unsigned int offset,const void *src, int n);

void SetLBON(unsigned int n);

void SetLBOFF(unsigned int n);

int GetLB(unsigned int n);

int SetLWBON(unsigned int n, unsigned int offset);

int SetLWBOFF(unsigned int n, unsigned int offset);

int GetLWB(unsigned int n, unsigned int offset);


//添加CRC函数

/* Table Of CRC Values for high-order byte */

unsigned char auchCRCHi[] = {

0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81,

0x40, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0,

0x80, 0x41, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x00, 0xC1, 0x81, 0x40, 0x01,

0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41, 0x01, 0xC0, 0x80, 0x41,

0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x00, 0xC1, 0x81,

0x40, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41, 0x01, 0xC0,

0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41, 0x01,

0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81, 0x40,

0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81,

0x40, 0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0,

0x80, 0x41, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x00, 0xC1, 0x81, 0x40, 0x01,

0xC0, 0x80, 0x41, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41,

0x00, 0xC1, 0x81, 0x40, 0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81,

0x40, 0x01, 0xC0, 0x80, 0x41, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0,

0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41, 0x01,

0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41,

0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81,

0x40

} ;


/* Table of CRC values for low-order byte    */

unsigned char auchCRCLo[] = {

0x00, 0xC0, 0xC1, 0x01, 0xC3, 0x03, 0x02, 0xC2, 0xC6, 0x06, 0x07, 0xC7, 0x05, 0xC5, 0xC4,

0x04, 0xCC, 0x0C, 0x0D, 0xCD, 0x0F, 0xCF, 0xCE, 0x0E, 0x0A, 0xCA, 0xCB, 0x0B, 0xC9, 0x09,

0x08, 0xC8, 0xD8, 0x18, 0x19, 0xD9, 0x1B, 0xDB, 0xDA, 0x1A, 0x1E, 0xDE, 0xDF, 0x1F, 0xDD,

0x1D, 0x1C, 0xDC, 0x14, 0xD4, 0xD5, 0x15, 0xD7, 0x17, 0x16, 0xD6, 0xD2, 0x12, 0x13, 0xD3,

0x11, 0xD1, 0xD0, 0x10, 0xF0, 0x30, 0x31, 0xF1, 0x33, 0xF3, 0xF2, 0x32, 0x36, 0xF6, 0xF7,

0x37, 0xF5, 0x35, 0x34, 0xF4, 0x3C, 0xFC, 0xFD, 0x3D, 0xFF, 0x3F, 0x3E, 0xFE, 0xFA, 0x3A,

0x3B, 0xFB, 0x39, 0xF9, 0xF8, 0x38, 0x28, 0xE8, 0xE9, 0x29, 0xEB, 0x2B, 0x2A, 0xEA, 0xEE,

0x2E, 0x2F, 0xEF, 0x2D, 0xED, 0xEC, 0x2C, 0xE4, 0x24, 0x25, 0xE5, 0x27, 0xE7, 0xE6, 0x26,

0x22, 0xE2, 0xE3, 0x23, 0xE1, 0x21, 0x20, 0xE0, 0xA0, 0x60, 0x61, 0xA1, 0x63, 0xA3, 0xA2,

0x62, 0x66, 0xA6, 0xA7, 0x67, 0xA5, 0x65, 0x64, 0xA4, 0x6C, 0xAC, 0xAD, 0x6D, 0xAF, 0x6F,

0x6E, 0xAE, 0xAA, 0x6A, 0x6B, 0xAB, 0x69, 0xA9, 0xA8, 0x68, 0x78, 0xB8, 0xB9, 0x79, 0xBB,

0x7B, 0x7A, 0xBA, 0xBE, 0x7E, 0x7F, 0xBF, 0x7D, 0xBD, 0xBC, 0x7C, 0xB4, 0x74, 0x75, 0xB5,

0x77, 0xB7, 0xB6, 0x76, 0x72, 0xB2, 0xB3, 0x73, 0xB1, 0x71, 0x70, 0xB0, 0x50, 0x90, 0x91,

0x51, 0x93, 0x53, 0x52, 0x92, 0x96, 0x56, 0x57, 0x97, 0x55, 0x95, 0x94, 0x54, 0x9C, 0x5C,

0x5D, 0x9D, 0x5F, 0x9F, 0x9E, 0x5E, 0x5A, 0x9A, 0x9B, 0x5B, 0x99, 0x59, 0x58, 0x98, 0x88,

0x48, 0x49, 0x89, 0x4B, 0x8B, 0x8A, 0x4A, 0x4E, 0x8E, 0x8F, 0x4F, 0x8D, 0x4D, 0x4C, 0x8C,

0x44, 0x84, 0x85, 0x45, 0x87, 0x47, 0x46, 0x86, 0x82, 0x42, 0x43, 0x83, 0x41, 0x81, 0x80,

0x40

} ;


unsigned int crc16(unsigned char *puchMsg,unsigned char usDataLen)  // puchMsg message to calculate CRC upon

{                                           // usDataLen quantity of bytes in message

unsigned char uchCRCHi = 0xFF ;                 // high byte of CRC initialized

unsigned char uchCRCLo = 0xFF ;                 // low byte of CRC initialized

unsigned int  uIndex  ;                         // will index into CRC lookup table

while (usDataLen--)                     // Pass through message buffer

{

uIndex = uchCRCHi ^ *puchMsg++ ;    // calculate the CRC

uchCRCHi = uchCRCLo ^ auchCRCHi[uIndex] ;

uchCRCLo = auchCRCLo[uIndex] ;

}

return (((unsigned int)(uchCRCHi) << 8) | uchCRCLo) ;

}


void ProcessComx(int fd)

{

unsigned char receive[1024];

unsigned char send[1024];

int i,timeout,crc_result;

unsigned short LwValue;


Delay(100);//ms


printf("COM1 Working...\r\n");

if (GetLB(0)==1)

{

LwValue=Read_LW(3);

if(GetLB(1)==1)

SetLBOFF(1);

else

SetLBON(1);


if(GetLWB(4, 5)==1)//lw4.5

SetLWBOFF(4,5);

else

SetLWBON(4,5);

printf("LW3=%d\r\n", LwValue);

send[0] = 1;

send[1] = 3;

send[2] = 0;

send[3] = 0;

send[4] = 0;

send[5] = 2;

send[6] = (unsigned char)(crc_result>>8);

send[7] = (unsigned char)crc_result;

crc_result=crc16(send,6);

WriteData(fd, send, 8);

timeout = 100;//ms

ReadData(fd, receive, 1024, timeout);

//for(i=0;i<10;i++)

// printf("%d ", receive[i]);

Write_LW(0, receive[3]*0x100+receive[4]);

Write_LW(1, receive[5]*0x100+receive[6]);

}

}

为什么串口没收到显示




福州欧瑞机械

  • 精华:0帖
  • 求助:0帖
  • 帖子:0帖 | 19回
  • 年度积分:0
  • 历史总积分:0
  • 注册:2015年5月11日
发表于:2015-05-11 20:18:44
1楼

学习,虽然现在还看不懂这些语言。

福州欧瑞机械

  • 精华:0帖
  • 求助:0帖
  • 帖子:0帖 | 19回
  • 年度积分:0
  • 历史总积分:0
  • 注册:2015年5月11日
发表于:2015-05-11 20:19:20
2楼

我也是网络上买的ET100,刚刚收到3天。是来学习的。


热门招聘
相关主题

官方公众号

智造工程师