免费的西门子技术支持 点击：100846 | 回复：2872
本人愿和同道中人共同探讨西门子技术范围包括（200/300/400/Wincc/Hmi)
技术文章参考博客！ http://jiansiting.gkbk.com
About Wincc show many error how do you clear them
Error code
Possible causes Remedy
0x80004005
Your Windows user isn‘t a member of the "SIMATIC HMI" and "Main users" user groups. The "SIMATIC HMI" user group is created when WinCC is installed. In order to use WinCC without encountering any problems, the Windows users must belong to this group.
The Windows user should not be a member of any other user groups with restricted rights because user rights are cumulative. As soon as the rights of a group are restricted, the rights of the corresponding user are restricted accordingly.
There is detailed information available in the WinCC Online Help under "WinCC Information System > Installation Notes > Installation Requirements"
0x80010105
or
0x8004611c
The Windows user‘s rights are inadequate. Change the user‘s rights. The Windows user who is logged in should have the following properties:
? Main user rights at least
? Be a member of the SIMATIC HMI group
? In the case of server-client systems, the user must be known on both systems.
0x8003002
The project is no longer located at its "old" place, or the project file "
0x8007035
This error message is output if a firewall and anti-virus software or such like are enabled on the computer. Only install anti-virus software which is approved for WinCC. The Windows firewall is released from WinCC V6.2; other firewalls are not approved. Older versions of WinCC may not be operated in connection with a firewall.
You can find details of which anti-virus software is approved for WinCC in Entry ID 24122009.
0x80080005
The DCOM interface in Windows is disabled. Enable the DCOM interface in the Windows registry.
Alternatively, the changes can also be made manually:
? Open your computer‘s registry by clicking "Start > Run..." and then entering the command "regedit".
? Open the path "HKEY_LOCAL_MACHINE > SOFTWARE > Microsoft > OLE".
? Double-click "EnableDCOM". A value-entry window opens; enter "Y".
Important:
As a general rule, no warranty can be provided for direct changes made to the registry because this is the responsibility of the user. In any event, you are advised to make a backup of the registry before undertaking the actions described here. Furthermore, these settings are computer-specific. This means that when you copy the project to another computer, you must make the settings there again.
0x8007046a
This error message might be displayed when you access released elements on a server from a client:
"not enough server storage is available for this command" The error message is output when you start WinCC. If you start WinCC from the SIMATIC Manager, the hourglass is displayed and WinCC is not started. The following entry is in the Windows event display:
"Event ID 2011, IRPStackSize too small
The configuration parameter "irpstacksize" of the server service is too small to use a local device.
This problem can occur if too low a value has been defined on the server for the Registry entry "IRPStackSize".
Define a higher value for the Registry entry "IRPStackSize" to clear the problem. Use the following procedure:
1. Click on "Start > Run...", enter "regedit" and click on "OK".
2. Click on the following subcode in the Registry:
"HKEY_LOCAL_MACHINE\SYSTEM
\CurrentControlSet\Services\lanmanserver\Parameters"
If the value "IRPStackSize" is not available, proceed as follows:
o In the menu you ｓｅｌｅｃｔ "Edit > New > DWORD Value".
o Name the value "IRPStackSize". Pay attention here to the upper-case and lower-case lettering.
3.ｓｅｌｅｃｔthe item "Modify" in the pop-up menu.
4. Enter a higher value in the Value field. The standard value is 15 according to the "Microsoft Knowledge Base". This value is also used when there is no "IRPStackSize" entry. The value range is 11 to 50 (decimal). Microsoft recommends increasing the value by 3. Then click on "OK".
5. Close the Registry editor and restart the computer.
\CurrentControlSet\Services\lanmanserver\Parameters"
If the value "IRPStackSize" is not available, proceed as follows:
o In the menu you ｓｅｌｅｃｔ "Edit > New > DWORD Value".
o Name the value "IRPStackSize". Pay attention here to the upper-case and lower-case lettering.
3.ｓｅｌｅｃｔthe item "Modify" in the pop-up menu.
4. Enter a higher value in the Value field. The standard value is 15 according to the "Microsoft Knowledge Base". This value is also used when there is no "IRPStackSize" entry. The value range is 11 to 50 (decimal). Microsoft recommends increasing the value by 3. Then click on "OK".
5. Close the Registry editor and restart the computer.
回复内容:
对:剑思庭 关于to 李建波，首先我不了解你的网络结构，你叙述的是不时这个意思，触摸屏连接plc，plc在连接变频器？如果是触摸屏你在组态的时候，一个画面的数据关联到plc的数据区，应该是一个双字，就是md或者vd区域。它直接就会显示500。然后你再把这个数值送到变频器。 内容的回复：
剑工，你说的不错，我的网络确实是变频器端子到PLC，然后由PLC再到变频器
再问你一个问题，关于用PLC控制变频器
让变频器升速降速的问题
在触摸屏上组态一个升速的按钮，点击升速，显示速度输出值就按一定比率升速
请问剑工，这个升速的程序用S7200该怎样实现？
- 如果是你，亚控，力控，紫金桥，...
[3896] - 施耐德软件任你拿[5142]
- wincc的vbs内部函数 HMIRunt...[8584]
- eplan自己绘制的元件，如何放...[25643]
- 送三菱触摸屏软件GT Designe...[2753]
- PLC空操作指令及其典型应用说...[2110]
- ab plc中文指令集[3177]
- 欧陆590直流驱动器的电脑软件...[2706]
- 智创强档推出新顶级.hk域名首...[2117]
- 监控组态软件的发展趋势与现...[17102]
官方公众号
智造工程师
-
客服
-
小程序
-
公众号
工控网智造工程师好文精选
