原创FANUC机器人配置profinet说明 点击:2613 | 回复:7



torunking

    
  • 精华:0帖
  • 求助:0帖
  • 帖子:5帖 | 10回
  • 年度积分:0
  • 历史总积分:237
  • 注册:2017年2月23日
发表于:2018-05-17 10:10:24
楼主

详细资料见附件

How to download PROFINET board firmware

Version 1.0

September 4, 2013

 

1. About this document

This document is a supplement of PROFINET I/O OPERATORS MANUAL.

This document (version 1.0) explains how to download the firmware to Siemens

CP1604/CP1616 PROFINET hardware.

 

2. Requirement for download function

If the controller is R-30iA, the software version must be V7.70P22 or later for R-30iA.

If the controller is R-30iB, download function is supported.

 

3. Firmware download from Download screen at CTRL START

  1. Copy the firmware file (*.fwl) to a memory card, or other devices.

  2. If the robot controller power is on, turn off the controller.

  3. With the PREV key and the NEXT key held down on teach pendant, turn on the controller.

    Configuration menu is displayed.

System version: V8.1035 2/10/2012

---------- CONFIGURATION MENU ----------

1. Hot start
2. Cold start
3. Controlled start
4. Maintenance

Select >

  4. Select 3. Controlled Start. The setting screen for the controlled start menu appears.


Tool Setup                                  
                                      1/6
 1 F Number:                     F00000
 2 KAREL Prog in select menu:    YES
 3 Remote device:                  UOP
 4 Intrinsically safe TP:         NO


[ TYPE ]                                

  5. Press MENU.

  6. Select Next page.

  7. Select Next page again.

  8. Select 1. PROFINET.

  9. PROFINET Download screen appears. The firmware file can be downloaded to PROFINET

    board (CP1604/CP1616) by the oepration in this screen (procedure 3-1).

 


Setup PROFINET IO                         
 Download                      1/4

 1.Download XDB file
     XDB file name
 2.[ MC:pcst_1.xdb                     ]
 3.Download firmware
     Firmware file name
 4.[ MC:fw16xx-2.5.0.0.19.fwl         ]


[ TYPE ]          [Other]              >

 10. Insert the memory card, or other device where the firmware file is copied.

 

Procedure 3-1 : Download of firmware

  To download firmware, please follow the procedure below.

1. Check the firmware file name with device path (e.g. MC:) displayed in the screen. 

If the file name is not equal to the firmware file to be download, change the file name.

The file name must be specified with device path.

2. Move cursor to “Download firmware”, and press Enter.

3. Dialogue with a message like “This operation may take 7 minutes” shows up.

Answer “Yes” to proceed.

4. Wait for the completion of download. Never turn off the robot controller during the download,

 otherwise firmware in PROFINET board might be erased, and PROFINET board is no longer

 operational until firmware is not recovered (Please see Procedure 3-2).

5. The result of download shows up in the screen when download has finished or failed.

6. Cold start the robot controlle (Press FCTN key. Select 1. Cold Start).

 

NOTE: Please power off/on the controller after firmware update is completed. If the external

power supply of CP1604/CP1616 is connected, remove it before cycle power and connect it

again after power up.

 

Procedure 3-2 : Recovery in case the firmware of PROFINET board is erased.

In case of the failure of firmware download by a corrupted firmware file, or the robot controller is

turned off during firmware download, the firmware of PROFINET board might be erased. Then

the PROFINET board is no longer operational until the firmware is recovered.

 

To recover the firmware, prepare the firmware that can be downloaded successfully, and follow

the procedure below. The firmware download can be tried again after firmware recovery.

 

1. Set $PNIO_DL.$NO_FIRM_ST to 1. Please note that the system variable will return to 0 at

next start up of the robot controller.

2. Perform “Controlled Start” of the robot controller.

3. Open the setup PROFINET download screen, and follow the procedure 3-1 to download the

firmware. Please note that PROFINET board is not operational until firmware is downloaded.

 

 

 


正在下载,请等待……
下载附件需5积分!




云雨忧清

  • 精华:0帖
  • 求助:1帖
  • 帖子:9帖 | 178回
  • 年度积分:0
  • 历史总积分:154
  • 注册:2015年8月05日
发表于:2018-05-17 14:24:43
1楼
谢谢楼主,楼主真是好人呢啊!

域外来风

  • 精华:0帖
  • 求助:3帖
  • 帖子:14帖 | 1748回
  • 年度积分:72
  • 历史总积分:3405
  • 注册:2016年11月22日
发表于:2018-05-18 08:08:17
2楼

谢谢分享!

从冰点到沸点

  • 精华:0帖
  • 求助:0帖
  • 帖子:3帖 | 20回
  • 年度积分:1
  • 历史总积分:161
  • 注册:2016年10月07日
发表于:2018-12-26 08:47:01
3楼

谢谢楼主,楼主真是好人呢啊!

工业控制qq

  • 精华:0帖
  • 求助:0帖
  • 帖子:0帖 | 35回
  • 年度积分:0
  • 历史总积分:293
  • 注册:2018年1月23日
发表于:2019-03-11 14:55:57
4楼

里面内容是中文吗?

杨坤QQ

  • 精华:0帖
  • 求助:0帖
  • 帖子:0帖 | 137回
  • 年度积分:0
  • 历史总积分:72
  • 注册:2018年6月09日
发表于:2019-03-12 15:37:39
5楼

感谢楼主!谢谢分享!

xguox

  • 精华:0帖
  • 求助:0帖
  • 帖子:0帖 | 75回
  • 年度积分:0
  • 历史总积分:86
  • 注册:2017年11月06日
发表于:2019-04-18 10:39:12
6楼

川崎机器人我们单位没有,既然进来了就留个脚印吧。感谢楼主

信仰小男孩

  • 精华:0帖
  • 求助:0帖
  • 帖子:1帖 | 42回
  • 年度积分:0
  • 历史总积分:52
  • 注册:2016年11月19日
发表于:2019-04-28 19:37:54
7楼

积分少,下不了啊


热门招聘
相关主题

官方公众号

智造工程师